Flo King BXL500 Repair Parts

Flo King Low-Profile BXL5000 Repair Parts
Several parts shown below are available in CPVC plastic (gray in color) and polypropylene (white). Where a separate part number does not exist, specify CPVC or polypro when ordering. Some parts also available in Kynar (PVDF) and stainless steel. Contact us for information on Kynar and SS replacement parts. See this link for BXL5000 Disassembly & Belt Replacement Instructions.

BXL5000 Motor

50XL MOTOR
Motor for Low-Profile BXL5000

Includes Motor Pulley, Fan Cover, Fan Cover Hardware, Fan Blade, Adjustable Stand-Off, & 50XL MBHW Motor Base Hardware (four SS Hex-Head 1/4-20 Screws, 1-1/4" Long), four 1/4" SS Lock Washers, & four 1/4" SS Flat Washers

Standard BXL5000 Motor is 0.75 hp. A special "High-Density" Motor rated at 1 hp is used primarily to pump thick solutions (e.g., sulfuric/phosphoric acid electropolishing).

SHR Swiveling Impeller Housing

50XL SHR
CPVC Swiveling Impeller Housing
for BXL5000 (gray in color)

Includes three Filter Screws (50XL FS), Lock Screw (50XL SHLS) & Teflon Strap
(50XL STRAP).

If you need polypro (white),
Order # is 50XL SHR-PP.

Fits BX3000, BX5000, BXL2500
& BXL5000.

Filter Screw

FS6
CPVC Filter Screw, Pack of Six.
Thread Length 3/4" (1.9 cm),
gray in color

If you need polypro (white),
Order # is FS6-PP

Fits BX650, BX1200, BX3000,
BX5000, BXL2500 & BXL5000.
Thread size is 3/8-16.

Lock Screw

50XL SHLS
CPVC Lock Screw for BXL5000
Swiveling Impeller Housing.
Thread Length 0.5 inch (1.27 cm),
gray in color

If you need polypro (white),
Order # is 50XL SHLS-PP.

Fits BX3000, BX5000, BXL2500
& BXL5000.

Impeller BXL5000

50XL IMP
CPVC Impeller for BXL5000
(gray in color)

Includes 50XL TSS (Super Slinger)
& 50XL TIW (Impeller Washer)

If you need polypro (white),
Order # is 50XL IMP-PP.

TSS Super Slinger

50XL TSS
Super Slinger for BXL5000

Fits BX3000, BX5000, BXL2500
& BXL5000.

TIW Impeller Washer

50XL TIW
Impeller Washer for BXL5000

Fits BX3000, BX5000, BXL2500
& BXL5000. Outside Diameter as
shipped from factory is 3/4" (19.05 mm)

VBS Boot Seal

50XL VBS
Boot Seal for BXL5000

Fits BX3000, BX5000, BXL2500
& BXL5000

50XL STRAP

50XL STRAP
Teflon Strap for
Swiveling Impeller Housing

Secures Impeller Housing to
pump Body. Fits BX3000, BX5000,
BXL2500 & BXL5000. Strap is about
9-3/8" long x 1/4" wide (23.33 cm
x 0.635 cm).

50XL NB15
New-Style Belt for BXL5000

Manufacturer's number on Belt
is usually Gates 6705M15 HNBR.

Also fits BXL2500 with
Long Motor Base (15").

Old-Style Belt for BXL5000 pumps made prior to Dec. 2002 may be marked Bando Synchro-Link 200 XL 050 A04112.

50XL NSHPB

50XL NSHPB (__LENGTH)
Teflon-Covered Shaft with Stainless-Steel Shaft Pulley & Shaft Bearings

Includes 50XL NSPR (New-Style SS Shaft Pulley), two Shaft Bearings, Teflon-Covered Shaft, 50XL IHW (Inside Heel Washer,
1-5/8 x 5/8"), & VBS (Boot Seal)

When ordering, specify pump-body length by measuring "A" Dimension on drawing at this link: BXL5000 Specs

Standard Shaft is made of stainless steel. Titanium-Tip Shaft and Hastelloy-C276-Alloy-Tip Shaft available as a precaution for aggressive solutions that may
attack SS. All Shafts covered with Teflon Heat-Shrink Tubing.

BXL5000 Shaft Only

50XL SHAFT (__LENGTH)
Teflon-Covered Shaft

When ordering, specify pump-body
length by measuring
"A" Dimension on drawing at this link:
BXL5000 Specs

Standard Shaft is made of stainless steel. Titanium-Tip Shaft and Hastelloy-C276-Alloy-Tip Shaft available as a precaution for aggressive solutions that may attack SS. All Shafts covered with Teflon Heat-Shrink Tubing.

50XL HSBBA

50XL HSBBA (__LENGTH)
Heel, Shaft, Shaft Bearing
& Belt Assembly for BXL5000

Includes 50XL NSPR (New-Style SS Shaft Pulley), two Shaft Bearings, Teflon-Covered Shaft, Heel, Inside Heel Washer
Outside Heel Washer, Heel Hardware,
VBS (Boot Seal) & 50XL NB15 Belt.

When ordering, specify pump-body length by measuring "A" Dimension on drawing at this link: BXL5000 Specs

Standard Shaft is made of stainless steel. Titanium-Tip Shaft and Hastelloy-C276-Alloy-Tip Shaft available as a precaution for aggressive solutions that may
attack SS. All Shafts covered with Teflon Heat-Shrink Tubing.

50XL BBR

50XL BBR (__LENGTH)
Base & Body for BXL5000

Includes four Spacers &
50XL PBHW Pump Base Hardware
(four 1/4-20 SS Screws, 1-3/4" Long
Phillips Head, Flat)

For repairs outside of the Flo King factory, you must order the 50XL BBR Base & Body Assembly to avoid machining operations associated with separate purchase of either the Base or the Body.

Specify pump-body length and pump material of construction when ordering.
To determine pump-body length, measure "A" Dimension on drawing at this link: BXL5000 Specs

To identify material of construction, check color of pump Body submerged in solution. Gray in color is CPVC; white is polypro. Those are the two most popular materials. We also offer stainless steel and PVDF (Kynar).

50XL PBHW
Pump Base Hardware for BXL5000

Four 1/4-20 SS Screws, 1-3/4" Long, Phillips Head, Flat. Hardware secures Pump Base
& Body to Motor Base.

50XL SHBEAR
Shaft Bearing for BXL5000

Sold individually. Two required.

50XL NSPR New Shaft Pulley

50XL NSPR
New-Style Shaft Pulley for BXL5000

Stainless-Steel Shaft Pulley with Keyway

50XL PR Old Shaft Pulley

50XL PR
Old-Style Shaft Pulley for BXL5000

Aluminum Shaft Pulley with holes
for set screws. Used only on BXL5000
units made prior to Dec. 2002.

50XL MB15

50XL MB15
Motor Base Assembly
with Heel & Belt for BXL5000

Includes 50XL NB15 Belt, Inside Heel Washer, Outside Heel Washer, & 50XL MBHW Motor Base Hardware (four SS Hex-Head 1/4-20 Screws, 1-1/4" long; four 1/4" SS Lock Washers; & four 1/4" SS Flat Washers)

Also fits BXL2500 with
Long Motor Base (15").

Motor Base made of aluminum.
Also available in stainless steel
on special-order basis.

BXL5000 Motor Base Hardware

50XL MBHW
Motor Base Hardware for BXL5000

Secures Motor Base to Motor.
Four SS Hex-Head 1/4-20 Screws (1-1/4" Long), four 1/4" SS Lock Washers, &
four 1/4" SS Flat Washers.

50XL SPC (Spacer)

Sold individually. Includes one
1/4-20 SS Screw, 1-3/4" Long,
Phillips Head, Flat.

Four Spacers required per pump.

50XL MOTBEAR
Motor Bearing for BXL5000

Sold individually. Two required.

BXL5000 Heel

50XL MBH
Heel for BXL5000

Includes Inside Heel Washer, Outside Heel Washer, & Heel Hardware (three
10-24 x 1/2" Black Socket Cap Screws
& three #10 SS Flat Washers)

50XL HLHDW

50XL HLHDW
Heel Hardware for BXL5000

Three 10-24 x 1/2" Black
Socket Cap Screws & three
#10 SS Flat Washers

Inside Heel Washer

50XL IHW
Inside Heel Washer for BXL5000

1-5/8" OD (41.2 mm); hole diameter 5/8" (15.8 mm). Fits BXL2500 & BXL5000.

Included with purchase of Heel.

Outside Heel Washer

50XL OHW
Outside Heel Washer for BXL5000

1-7/16" OD (36.5 mm); hole diameter 15/16" (23.8 mm). Fits BXL2500
& BXL5000.

Included with purchase of Heel.

50XL BDC15

50XL BDC15
Belt-Drive Cover for BXL5000

Includes ten 8-32 x 5/16 Phillips
SS Panhead Screws & ten 8-32
SS Flat Washers

Also fits BXL2500 with
Long Motor Base (15").

50XL BDCHW
Belt-Drive Cover Hardware
for BXL5000

Ten 8-32 x 5/16 SS Phillips
Panhead Screws
& Ten 8-32 Flat SS Washers

50XL TEF

50XL TEF
Teflon Heat-Shrink Tubing for
BXL5000 Shaft

Used for all BX3000, BX5000, BXL2500
& BXL5000 Shafts. Sold by the inch.
Outside diameter 0.70".

50XL NPR New SS Motor Pulley

50XL NPR
New-Style Motor Pulley for BXL5000

Stainless steel. Left-hand thread.

Also fits BXL2500.

50XL PR Old Motor Pulley

50XL PR
Old-Style Motor Pulley for BXL5000

Aluminum Motor Pulley. Left-hand thread. Used only on BXL5000 units made prior
to Dec. 2002.

Discontinued Motor Pulley

DISCONTINUED
Original 50XL Motor Pulley

Original aluminum Motor Pulley with Stem. No longer available.

BXL5000 Fan Covers

50XL FCOV
Fan Cover for BXL5000

Specify whether you have a Baldor or Leeson motor when ordering:
(top photo) Fan Cover for Baldor motor,
6 x 1-1/2" (15.24 x 3.81 cm);
(middle photo) Fan Cover for new-style Leeson motor, 6 x 1-3/4" (15.24 x 4.44 cm); (bottom photo) Fan Cover for old-style Leeson motor, 5-3/4 x 2-1/4"
(14.6 x 5.71 cm)

Note: Color of current BXL5000 Fan Covers is black. Only units made prior to Dec. 2002 have blue Fan Covers.

BXL5000 Fan Blades

50XL FBR
Fan Blade for BXL5000

Includes Fastener (Screw or Clip)

Specify whether you have a Baldor or Leeson Motor when ordering:
(top photo) Fan Blade with Screw for Baldor Motor, (bottom photo) Fan Blade with Clip for Leeson Motor.

50XL Adjustable Stand-Off

50XL ASO
Adjustable Stand-Off for BXL5000

Welded onto Motor at factory.

Shaft Tip

TITANIUM-TIP SHAFT
OR HASTELLOY-TIP SHAFT

Titanium-Tip or Hastelloy-C276-Alloy-Tip Shaft is a special factory-installed item recommended as a precaution for aggressive acids that may attack standard stainless-steel Shaft on BX3000, BX5000, BXL2500 & BXL5000. Tip is 2-1/2" long (6.35 cm) and threads onto standard SS Shaft & into Impeller Insert.

Impeller Insert

IMPELLER INSERT

Threaded stainless-steel Insert is installed on all BX3000, BX5000, BXL2500 & BXL5000 Impellers at Flo King factory. Special titanium Inserts and Hastelloy-C276-alloy Inserts are available as a precaution for aggressive solutions that may attack standard SS Insert. Material of construction should be same for Shaft (or Shaft Tip) and Insert.

LOOKING FOR MORE
BXL5000 PARTS?

Click this link for photos and
descriptions of BXL5000 new
parts and accessories.