Custom Masters/Flo King
Phone: 407-331-4634
Fax: 407-331-0575


BX1200 MaterialGeneral guidelines for selecting BX1200 pump material of construction are shown below.

Disclaimer: This is a general guide based on user operating experiences with Flo King Filter Systems. The information presented may not be suitable for every application.

CPVC as Pump Material of Construction
CPVC (gray in color) is our standard, least-expensive, and by far the most popular pump material of construction for the BX1200. CPVC is generally recommended for neutral solutions and many acids at a wide range of temperatures.

CPVC is also often used in mildly alkaline solutions at temperatures up to 160-180 (71 to 82 C). However, CPVC may become brittle, then crack and split, in some highly alkaline solutions, even at relatively low temperatures (examples: alkaline non-cyanide zinc or aggressive, highly caustic alkaline cleaners).

Typical CPVC applications include: nickel electroplating, acid copper plating, acid tin plating, acid zinc plating, chromating, decorative chrome plating, some hard chrome plating applications, lower-temperature electroless nickel plating (185 - 190 F, 85 - 89 C), passivating, pickling, rinsing, anodizing, low-temperature seals, mild alkaline cleaners. Many customers use CPVC in cyanide silver, cyanide copper and cyanide zinc, though some prefer polypro.

Polypropylene as Pump Material of Construction
Polypropylene (white in color) can also be used in neutral solutions and some acids at a wide range of temperatures.

Polypropylene is generally satisfactory for mild to moderately aggressive alkaline solutions at temperatures up to 160 - 170 F (70 - 77 C). However, at temperatures well above 170 F (77 C) or in highly concentrated, high-pH caustic solutions, polypropylene may swell, causing serious pump problems. In cases of aggressive caustics — especially at higher temperatures — only stainless steel pump construction is recommended.

Polypropylene is readily attacked by concentrated chromic acid and cannot be used in applications such as hard chrome plating or chromic acid anodizing.

Polypropylene costs about 15 percent more than CPVC for the BX1200.

Typical polypro applications include: alkaline non-cyanide zinc plating, zincating, electroless nickel up to about 194 F (90 C), gold, high-purity precious-metals plating processes, mild alkaline cleaners

Kynar (PVDF) as Pump Material of Construction
Kynar is a high-temperature plastic that can be used in neutral solutions up to about 215 F (105 C) and also in many acids at higher temperatures than CPVC can withstand.

However, like CPVC, Kynar is absolutely not recommended for highly aggressive alkaline solutions. It tends to become brittle, then crack and split in aggressive caustics.

Typical Kynar applications include: hard chrome plating, chromic acid etches, chromic acid anodizing, electroless nickel solutions well above 190 F (88 C), high-temperature seals following anodizing (sometimes up to 212 F, 100 C), and high-temperature sulfuric/phosphoric acid electroplating solutions.

Kynar is expensive — about 60 percent more than CPVC and 40 percent more than polypro for the BX1200.

Stainless Steel as Pump Material of Construction
Stainless steel (SS) is the material of choice for highly aggressive alkaline solutions at high temperatures — typically from 180 to 200 F (70 to 93 C).

Typical SS applications include: caustic high-pH cleaners, caustic strippers, caustic permanganate solutions, and black oxide (up to about 205 F, 96 C).

The BX1200 is available in stainless steel, but only in the 10-inch-long pump-body length. The SS BX1200 costs about 170 percent more than CPVC, 133 percent more than polypro, and 70 percent more than Kynar.

Most customers use SS pumps strictly for recirculation (without filter cartridge attached).


There are many solutions in which the Flo King system is effective.

Click this link to see pump material recommendations for many popular electroplating and other metal-finishing applications.


BX1200 Shaft MaterialsUnless otherwise specified, all Flo King pumps have an internal shaft made of 303 stainless-steel covered with Teflon heat-shrink tubing. In most cases, this works well, but when there is a failure, it almost always occurs when aggressive acids attack the SS Shaft where the Impeller screws onto the Shaft threads. This may happen because of (1) pinholes or other imperfections that develop in the Teflon coating, (2) wear and tear over time, or (3) objects that are sucked into the pump and damage the Teflon heat-shrink tubing. Caution: If using the pump strictly for recirculation (without filter cartridge attached), always install a Pump Strainer Adapter (PSA) to protect the Impeller, Shaft, and Teflon heat-shrink tubing from damage due to any foreign objects that might be in solution. See this link for PSA photo.

When to Consider Alternative Internal-Shaft Materials: If a solution is known to aggressively attack stainless steel, an internal titanium or Hastelloy Shaft is strongly recommended as a precaution. All Shafts are covered with Teflon Heat-Shrink Tubing.

   • Some Titanium Internal-Shaft Applications: Sulfuric acid anodizing, acid copper plating (sulfuric acid), hard chrome plating (non-fluoride type), chromic acid etch. Note: Titanium Shaft not available for BX1200-14 or BX1200-16.

   • Hastelloy Internal-Shaft Applications: Hastelloy C276 is a nickel-chrome-molybdenum-tungsten alloy that has better resistance to fluorides than does titanium. It is the customer's responsibility to determine if the solution attacks both stainless steel and titanium. If you are unsure if Hastelloy is needed for your application, we suggest you contact the chemical supplier for advice. Note: Hastelloy Shaft not available for BX1200-4.

There are many Chemical Resistance Charts available on the internet. We encourage you to research those charts for plastic and metal compatibility information if you do not find what you need here.

Flo King Materials

CPVC (gray in color) is our standard, least-expensive and most popular pump material of construction for the BX1200. Polypro (white), preferred for some applications, costs more. For special applications, Kynar (PVDF) and stainless steel are available.