Custom Masters/Flo King
Phone: 407-331-4634
Fax: 407-331-0575
email: floking@sprintmail.com

 

Flo King BX5000 Repair Parts
Several parts shown below are available in CPVC plastic (gray in color) and polypropylene (white). Where a separate part number does not exist, specify CPVC or polypro when ordering. Some parts also available in Kynar (PVDF) and stainless steel. Contact us for information on Kynar and SS replacement parts. Motor Replacement: Instructions for replacing the BX5000 Motor are shown at this link. However, for repairs outside of the Flo King factory, many customers prefer to order the Motor with Balanced Shaft Attached (5000 MOTSHF) because it is much easier to install (does not require removal, re-installation and re-balancing of the old Shaft on the new Motor). See this link for Motor/Shaft Replacement Instructions.



SHR Swiveling Impeller Housing

5000 SHR
Swiveling Impeller Housing for BX5000

Includes three Filter Screws, Lock Screw (5000 SHLS) & Teflon Strap
(5000 STRAP)
.

Order # in polypro is 5000 SHR-PP.

Fits BX3000, BX5000, BXL2500
& BXL5000
.




5000 STRAP

5000 STRAP
Teflon Strap for
Swiveling Impeller Housing

Secures Impeller Housing to
pump Body. Fits BX3000, BX5000, BXL2500 & BXL5000. Strap is about 9-3/8" long x 1/4" wide (23.33 cm x 0.635 cm).


 

Filter Screw

FS6
CPVC Filter Screw, Pack of Six.
Thread Length 3/4" (1.9 cm)


Order # in polypro is FS6-PP

Fits BX650, BX1200, BX3000,
BX5000, BXL2500 & BXL5000.
Thread size is 3/8-16.

 

Lock Screw

5000 SHLS
CPVC Lock Screw for BX5000
Swiveling Impeller Housing.
Thread Length 0.5 inch (1.27 cm)

Order # in polypro is 5000 SHLS-PP.

Fits BX3000, BX5000, BXL2500
& BXL5000
.

 

Impeller BX5000

5000 IMP
Impeller for BX5000

Includes 5000 TSS (Super Slinger) &
5000 TIW (Impeller Washer
)

Order # in polypro is 5000 IMP-PP.

 

TSS Super Slinger

5000 TSS
Super Slinger for BX5000

Fits BX3000, BX5000, BXL2500
& BXL5000.

TIW Impeller Washer

5000 TIW
Impeller Washer for BX5000


Fits BX3000, BX5000, BXL2500
& BXL5000
. Outside Diameter as
shipped from factory is 3/4" (19.05 mm)

 

VBS Boot Seal

5000 VBS
Boot Seal for BX5000


Fits BX3000, BX5000, BXL2500
& BXL5000

 

 

BX5000 Motor


5000 MOTOR

Motor for BX5000

Includes VBS Boot Seal, Fan Cover, Fan Blade, Spacers, & PBHW Pump/Motor Base Hardware (four 1/4-20 SS Screws, 1-3/4" Long, Phillips Head, Flat)

Standard BX5000 Motor is 0.75 hp. A special "High-Density" Motor rated at 1 hp is used primarily to pump thick solutions (e.g., sulfuric/phosphoric acid electropolishing). Three-phase Motors are also 1 hp.


Click here for BX5000 Motor Replacement Instructions


Spacer and Screw

5000 SPC (Spacer)

Sold individually. Includes one
1/4-20 SS Screw, 1-3/4" Long,
Phillips Head, Flat.

Four Spacers required per pump.
Fits BX3000 & BX5000.


5000 MOTSHF

5000 MOTSHF (__)
Motor with Balanced Teflon-Covered Shaft Attached for BX5000

Includes Fan Cover, Fan Blade, Spacers, VBS (Boot Seal), Super Slinger, Impeller Washer, & PBHW Pump/Motor Base Hardware (four 1/4-20 SS Screws, 1-3/4" Long, Phillips Head, Flat). Click here for BX5000 Motor/Shaft Replacement Instructions.

Specify pump-body length, voltage, and pump material of construction when ordering.

To determine pump-body length, measure "A" Dimension on drawing at this link: BX5000 Specs. To identify material of construction, check color of pump Body submerged in solution. Gray in color is CPVC; white is polypro. Those are the two most popular materials. We also offer stainless steel and Kynar (PVDF).

Standard Shaft is made of stainless steel. Titanium-Tip Shaft and Hastelloy-C276-Alloy-Tip Shaft available as a precaution for aggressive solutions that may attack SS. All Shafts covered
with Teflon Heat-Shrink Tubing.

5000 BBR


5000 BBR (__LENGTH)
Base & Body for BX5000

Includes PBHW Pump/Motor
Base Hardware (four 1/4-20 SS Screws,
1-3/4" Long Phillips Head, Flat
)

For repairs outside of the Flo King factory, you must order the 5000 BBR Base & Body Assembly shown above to avoid machining operations associated with separate purchase of either the Base or the Body.

Specify pump-body length and pump material of construction when ordering.

To determine pump-body length, measure "A" Dimension on drawing at this link: BX5000 Specs

To identify material of construction, check color of pump Body submerged in solution. Gray in color is CPVC; white is polypro. Those are the two most popular materials. We also offer stainless steel and PVDF (Kynar).



5000 Shaft Only


5000 SHAFT (__LENGTH)
Teflon-Covered Shaft


When ordering, specify pump-body
length by measuring
"A" Dimension on drawing at this link:
BX5000 Specs

Standard Shaft is made of stainless steel. Titanium-Tip Shaft and Hastelloy-C276-Alloy-Tip Shaft available as a precaution for aggressive solutions that may attack SS. All Shafts covered
with Teflon Heat-Shrink Tubing.

 

5000 TEF

5000 TEF
Teflon Heat-Shrink Tubing for
BX5000 Shaft


Used for all BX3000, BX5000, BXL2500
& BXL5000 Shafts. Sold by the inch.
Outside diameter 0.70".

 

 

5000 PBHW

5000 PBHW
Pump/Motor Base Hardware for BX5000

Four 1/4-20 SS Screws, 1-3/4" Long, Phillips Head, Flat. Hardware secures Pump Base
& Body to Motor Base.

 

BX5000 Motor Bearing

5000 MOTBEAR
Motor Bearing for BX5000

Sold individually. Two required.


BX5000 Universal Bracket

5000 UNBK
3" Universal Bracket


For tank mounting surfaces
up to 3" thick (7.62 cm). Includes two 1/4-20 x 3/4" Phillips Truss SS Machine Screws & Two 1/4-20 SS Flat Washers.

Fits BX3000 and BX5000. Can also be used on BX1200.

 

BX5000 Handle

5000 H
Handle for BX5000

Includes 5000 HHW Handle Hardware (two 1/4-20 SS Hex Cap Screws, 1/2" Long; & two 1/4-20 SS Lock Washers). Fits BX3000 & BX5000.

 

 

BX5000 Fan Covers

5000 FCOV
Fan Cover for BX5000

Specify whether you have a Baldor or Leeson motor when ordering:
(top photo) Fan Cover for Baldor motor,
6 x 1-1/2" (15.24 x 3.81 cm);
(middle photo) Fan Cover for new-style Leeson motor, 6 x 1-3/4" (15.24 x 4.44 cm); (bottom photo) Fan Cover for old-style Leeson motor, 5-3/4 x 2-1/4"
(14.6 x 5.71 cm)

 

BX5000 Fan Blades

5000 FBR
Fan Blade for BX5000

Includes Fastener (Screw or Clip)

Specify whether you have a Baldor or Leeson Motor when ordering:
(top photo) Fan Blade with Screw for Baldor Motor, (bottom photo) Fan Blade with Clip for Leeson Motor
.

 

Special Shaft Tip

TITANIUM-TIP SHAFT
OR HASTELLOY-TIP SHAFT

Titanium-Tip or Hastelloy-C276-Alloy-Tip Shaft is a special factory-installed item recommended as a precaution for aggressive acids that may attack standard stainless-steel Shaft on BX3000, BX5000, BXL2500 & BXL5000. Tip is 2-1/2" long (6.35 cm) and threads onto standard SS Shaft & into Impeller Insert.

 

Impeller Insert

IMPELLER INSERT

Threaded stainless-steel Insert is installed on all BX3000, BX5000, BXL2500 & BXL5000 Impellers at Flo King factory. Special titanium Inserts and Hastelloy-C276-alloy Inserts are available as a precaution for aggressive solutions that may attack standard SS Insert.

Material of construction should be same for Shaft (or Shaft Tip) and Insert.

 

LOOKING FOR MORE
BX5000 PARTS?

Click this link for photos and
descriptions of BX5000 new
parts and accessories.